(blissful guitar track) – [Tresha] good day guys,welcome again to the channel. It’s Tresha, and i am excitedto share one more first-class DIY proposal with you utilising 3D wall panels. You can situation thesepanels to your entryway, probably at the back of your sofa,or in the back of your television stand, you title it, the chances are endless of how you should use them. However i’m going to exhibit you a further manner. You realize me, i’ve toshow you a further means. If you don’t want toadhere it to the wall, this is an alternative for you. I wanted to provide a shoutout to CSI Wall Panels for sending me this percent for me to check out.It comes 12 in a %. The squares are about 191/2 inches with the aid of 19 half inches, so it covers, almost always likethree feet by way of nine ft of wall space. So you’ll be able to normally need more in case you wanted to do a function wall, but for this task,you best desire a percent. And this is what itlooks like within the inside of, you will have whole recommendations if you happen to desired to stick it to the wall, and it additionally comes with spacers as good. Before you start utilizing the panels, you wanna make certain it’s within the room the place you are going toinstall it for forty eight hours so it can get adjusted to the atmosphere. I chose this particulardesign, it can be referred to as hole, given that I thought it used to be very exciting, but they have got, if youdon’t like this design, they have so many more on hand, so make sure you investigate out the internet site.I’m going to put the hyperlink in thedescription box beneath so you will see exactlywhat i’m speaking about. And i consider it comesin two special colors, however the person who I chose isin usual off-white color. For this project you will desire a base, and that i selected wooden for this. So I went to residence Depot andgot a skinny piece of plywood. I want to say it is like half an inch, not up to half an inch in thickness, and it was form of giant, so I desired to divideit in 1/2 so i can have two panels on the wall.In addition to the plywood,I additionally bought four strips of the external nook molding. These are gonna be use toconceal the sides of the plywood. So the first thing that I didwas evenly sand the edges of the wood, I saw thatthere have been some difficult edges, and i wanted to make surethat that was delicate. Oh, and be sure to removeall the labels as good. Subsequent i’m going to gluethe molding to the perimeters of the plywood usingRapidFuse timber Adhesive. It sets in 30 seconds,it treatments in half-hour, and it can be a strong bond. I find it irresistible on the grounds that it can be fast. This is what it appears likewith the molding on it, it looks a lot cleaner now. I made up our minds to stain the woodas adverse to portray it, it can be absolutely as much as you what you decide, but I used this Minwax WoodFinish Penetrating Stain in English Chestnut. You easily wish to fire up your can and paint in the path of the grain. Make certain you comply with the instructional materials on the back of the can. I only used one coat.I waited about two minutes and then wiped the stain away with a rag. So here is what it looks like,it takes about eight hours for the stain to dry. It’s so much quicker ifyou determined to color it. So after I do that, I wantto comply with it up with a timber protectant, which is called Polyurethane. You want to ensure tostir up the can particularly just right earlier than you start using it, and use a clean brush when you do this, don’t use the same one asyou did with the wood stain, and follow the grain.I tremendously recommendreading the guidelines on the back of the can so you are aware of precisely the whole thing that you must do. While the base is drying, I’mdoing to color the 3D panels using a sponge brush. And i had some craftpaint already available. It can be an acrylic paint by craftsmart. I’m just gonna pour alittle bit of the paint into my paper plate, andjust work off of that. You are not looking for a wholelot for this project. In the event you observe, i am simply hanging paint on the tip of the comb. With your 3D panel,you’re just going to by means of doing an overview of thetop part of the design.After which, just color the within of it, or paint the inside of it, ‘scuse me. It’s just easier that means, so to keep within the line. Guys, when you’ve got somethingthat’s weighing in your mind, it is a pleasant mission todo due to the fact that while you paint, you disregard about the whole thing,to be honest with you. Like i am just focused onmaking definite I paint in between the traces, that is it! (laughing) I quite feel paintingthe top of the panel enhances the 3D result. What do you think? So the last factor that Idid was once glue the 3D panels to the bottom, and what you wish to have to do is check where you want it. What I did used to be house the panels to be three and 1/2 inchesfrom the highest and the backside and two and 1/four on the facet.Now that I determinedwhere I wanted the panels, I simply took a penciland marked the corners, flipped it over, and introduced E6000 to the back. Flipped it again over, waited24 hours before the glue dried, after which hung it on thewall, and that’s it, guys. This is a approach to have some quite cool, interesting 3D wall artwork thatdoesn’t ought to be affixed. In the event you guys have any tips ortricks that you simply would like to share simply drop it inthe comments section beneath. I would love to listen to from you. (happy guitar music) Thanks, guys, for looking at. Let’s join on Instagram. I’m @DESIGNSBYTRESHA, I wouldlove to look your DIY projects. So make sure you tag me. Additionally, determine out my different movies. I consider you’ll find it irresistible..